Quick answer
Solar farm decommissioning means taking the whole site apart, panels and everything else: inverters, transformers, switchgear, cables and mounting structures all have to be isolated, removed, transported and sent somewhere proper, with records to prove it. Recycling is usually the simplest step. The cost is driven by uncertainty, so owners who plan early, share a full inventory and test their electrical equipment before scrapping it get better prices and keep more value.
Key takeaways
- The recycling fee is a small part of the bill; removal, logistics, treatment, documentation and surprise work make up the rest.
- Sharing an inventory, photographs and access details early gives contractors less to guess and owners more reliable quotes.
- Test inverters, power modules and switchgear before they are classed as waste: some can be refurbished and kept as spares or put back into service.
Every solar farm has an end date. The planning permission or the land lease usually says the site must be cleared and the land handed back when generation stops. Decommissioning is the job of taking the whole site apart safely, sending every piece of equipment somewhere proper, and being able to prove it afterwards. It is closer than it sounds for a lot of owners: around 60% of the UK's larger ground-mounted solar farms (sites over 5 megawatts, roughly 5 GW between them) were built between 2010 and 2015, so their original inverters and switchgear are already well into middle age.
This article is for solar farm owners, asset managers and the landowners who lease them the ground. It covers where the money goes when a site comes down, why planning early brings the price down, and why the electrical equipment on a site deserves a proper test before anyone calls it waste. The topic came up in one of the sessions at Solar & Storage Live UK this September, and what was said there matches what we see from the repair bench.
Decommissioning covers the whole site
Most talk about solar end of life is about panel recycling. But a site also contains:
- mounting frames and the piles or foundations under them
- DC and AC cabling, much of it buried
- inverters, the power electronics that turn the panels' direct current into the alternating current the grid uses
- transformers, which step the voltage up for the grid connection
- switchgear, the heavy-duty switches and protection that connect the site to the network and disconnect it
- fencing, cameras, communications cabinets, and sometimes a battery system added later
National planning policy for large solar farms expects the panels and frames to be removed and buried cabling dug out, unless leaving something in the ground would do less harm. The same policy says consents of up to 40 years are typical. So the decommissioning plan written at the start is often used decades later, by people who were not there when it was written.
Recycling is often the simplest part
A lot has to happen before any equipment reaches a recycling plant. The site has to be isolated from the grid and made electrically safe. Then everything is dismantled, lifted, packed and transported. Each step depends on details: how many inverters there are, what the transformers weigh, whether a low loader can get down the access track in February.
Some items need specialist handling. Switchgear insulated with SF6 gas must have the gas recovered by qualified people before it is scrapped, and the gas must never be let out into the air. Transformer oil has its own treatment route. Solar panels fall under the UK's WEEE rules for electrical waste, with a producer-funded system for treating them. That system does not pay for anyone to take a site apart.
Uncertainty is what drives the price up
The point from the session that stuck with us is that uncertainty costs money. If a contractor does not know what equipment is on site, how much of it there is, what condition it is in or how to get vehicles to it, they have to price for the worst case. That shows up in the quote as extra labour, extra lifting, extra transport and a bigger contingency.
The fix is information, shared early. Owners who send an inventory, recent photographs and access details with the enquiry get quotes that are more reliable and easier to compare. A useful inventory lists every major item with its make, model, rating, location and condition; access details cover gates, track widths, weight limits and any seasonal restrictions the landowner has set.
The recycling fee is a poor measure of value
It is tempting to compare decommissioning offers on the recycling price per tonne or per panel. That number is a small slice of the real bill. The total also includes removal, logistics, treatment of each type of waste, paperwork, and the risk of unexpected work: buried cable that was never on the drawings, or foundations deeper than anyone expected.
A quote with a low recycling rate and a vague scope can turn out to be the most expensive one. The speaker's view was that recycling does not have to turn a profit for good decommissioning to pay off. The savings come from controlling cost, time and risk.
Test before you scrap
We would push owners one step further than the session did. Recycling is the right end for equipment that has genuinely finished its working life, and the wrong end for equipment that still works.
Inverters, power modules, control boards, transformers and switchgear often have years left in them when a site closes, particularly if they were replaced or refurbished part way through. Test them before they are classed as waste. A condition assessment can include insulation resistance tests, thermal imaging, a check of the capacitors and cooling fans inside inverters, oil analysis on transformers, and a review of each unit's fault and repair history. Equipment that passes has somewhere to go.
Spares for other sites. Some of the inverter models on older UK solar farms are no longer made or supported. An owner with more than one site can keep a tested unit as a spare for a sister site running the same equipment. Our article on obsolete parts inside working power systems explains why a qualified spare matters once the manufacturer has moved on.
Refurbishment and a second life. A power module, converter or control assembly can often be rebuilt in a workshop and put back into service. We do this routinely on STATCOM, UPS and battery systems, sometimes on site, as in our inverter rebuild inside a DSTATCOM.
A way round the queue for new equipment. New transformers and switchgear carry long delivery times, and our piece on transformer and switchgear lead times sets out how long. A tested unit that already exists can be worth more to someone than a new one delivered in two years.
Not everything will pass. Some equipment really is at the end of its life, and some is not worth the cost of refurbishing. Testing tells you which is which before the lorry arrives.
The same decision comes up mid-life. Many older UK solar farms are replacing their original central inverters as part of repowering, which means upgrading an operating site with newer equipment. The inverters coming out raise the same question on a smaller scale: scrap them, or test them and keep the good ones as spares for the rest of the fleet?
Material recovery starts on site
How equipment is handled on the day decides how much can be recovered. Separating it by type, packing it properly and avoiding damage during lifting all protect its value, whether it is heading for reuse or recycling. An inverter pulled out with its cables cut short and its door left open in the rain is much harder to put back into service. If reuse is part of the plan, write it into the method statement before dismantling starts, with the equipment to be kept labelled and handled separately.
A clear site is not a finished project
When the last lorry leaves, the owner still has to be able to show where every piece of equipment went, who received it, and how it was treated or reused. The landowner, the planning authority or anyone checking an environmental claim may ask. Waste transfer notes, hazardous waste consignment notes, treatment certificates and test records for anything reused all belong in that evidence trail.
The same records speed things up if the site is sold before it closes; see what to redo when a solar farm changes hands.
Agree responsibilities and destinations early
Before any work starts, the parties should agree who pays for what, what can be reused or recycled, which materials need specialist treatment, and who will receive each type of waste. That conversation is far easier years before the end date than weeks before it, especially when the lease, the planning condition and the operator's contract disagree.
Plan for the end from day one
Most of the useful decommissioning work happens long before decommissioning. Records kept through the life of the site make the end predictable and easier to demonstrate: an up-to-date asset register, commissioning results, fault logs, repair records and condition tests.
Three questions worth asking now:
- Could we send a contractor a full inventory tomorrow? Make, model, rating, location, condition and access for every major item.
- Which of our electrical equipment could be reused? Start with inverters, power modules and switchgear that are hard to replace or no longer supported by the manufacturer.
- Who keeps the paperwork? Decide now who holds the records and the evidence trail, so they survive changes of owner and operator.
Frequently asked questions
How long does a solar farm last before it is decommissioned?
Planning consents for large UK solar farms are usually time limited, and national policy says up to 40 years is typical. When the consent ends, the owner has to extend it or decommission the site and restore the land. Many owners replace inverters or other equipment part way through, so the kit removed at the end is not always the kit that was installed.
Who pays for solar panel recycling in the UK?
Solar panels are covered by the WEEE Regulations for electrical waste, and panels on solar farms are treated the same as household panels. Producers (manufacturers and importers) fund the treatment of panels through compliance schemes, although older panels can be handled differently. The site owner normally still pays for isolation, dismantling, packing, transport and restoring the land.
Can inverters from a decommissioned solar farm be reused?
Often, if they are tested first. An inverter that passes a condition assessment (insulation, capacitors, cooling, fault history) can be refurbished and kept as a spare for another site running the same model, or put back into service elsewhere. Units that fail go to recycling. The decision is much easier when the site has kept good repair records.
Planning a decommissioning, or replacing inverters on an older site? We test, repair and refurbish the power electronics we support, including STATCOM, UPS and battery systems, and can help you work out what is worth keeping before anything goes to recycling. If your question is about the solar inverters themselves, ask us and we'll tell you straight whether a repair is possible. Talk to our engineers or email sales@renewable-d.com.
Frequently asked questions
How long does a solar farm last before it is decommissioned?
Planning consents for large UK solar farms are usually time limited, and national policy says up to 40 years is typical. When the consent ends, the owner has to extend it or decommission the site and restore the land. Many owners replace inverters or other equipment part way through, so the kit removed at the end is not always the kit that was installed.
Who pays for solar panel recycling in the UK?
Solar panels are covered by the WEEE Regulations for electrical waste, and panels on solar farms are treated the same as household panels. Producers (manufacturers and importers) fund the treatment of panels through compliance schemes, although older panels can be handled differently. The site owner normally still pays for isolation, dismantling, packing, transport and restoring the land.
Can inverters from a decommissioned solar farm be reused?
Often, if they are tested first. An inverter that passes a condition assessment (insulation, capacitors, cooling, fault history) can be refurbished and kept as a spare for another site running the same model, or put back into service elsewhere. Units that fail go to recycling. The decision is much easier when the site has kept good repair records.
Tags
Working on a project like this?
Talk to our engineering team about your site, your grid connection or your power quality problem.
Get in touch


